change_par_submit_job(thickness, n) 结果
变量有两个,一个是w后面的数字,代表注浆圈厚度,一个是n,代表围岩与注浆圈渗透系数的比值。 代码 #-*-coding:mbcs-*-# Do notdeletethe followingimportlinesfromabaqusimport*fromabaqusConstantsimport*import__main__"""defchange_par_submit_job(thickness,n):"""thickness:groutcircle_thickness n:permeability...
(1 Create nstsncePartsBeamInstance TypeJ. _LLI .HIL . b . Ilk Lll_.ll叭Dependent (mesh on pat&qu 17、ot; Irde卩enderu (mesh on instanceNoter To change a Dependent instance'smesh, you muH edit its part's mesh. Auto-offset from other inst;)nceI OKApplyCancel图 1-10 Create In ...
parallelizationMethodExplicit=DOMAIN, scratch=’’, type=ANALYSIS, userSubroutine=’’) mdb.jobs[’EXAMPLE’].submit(consistencyChecking=OFF) mdb.jobs[’EXAMPLE’].waitForCompletion() ###change ### OUPUT ### execfile(’EXAMPLE_ODB.py’) ###change 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. ...
The coordinates of the current anchor point may change during the analysis if the local coordinate system is updated. Output variables SOF and SOM are both reported in the coordinate system considered.The center of forces SOCF is computed as the closest point to the centroid of the 34、 ...
The optimal choice of strainmeasuredepends on analysis type material behavior and to some degree personalpreference.By default the strain output in Abaqus/Standard is the “integrated”total strain output variable E. For large-strain shells membranes andsolid elements in Abaqus/Standard two other ...
*MODEL CHANGE, TYPE=ELEMENT, REMOVE Set-1 Set-1为所定义的单元集合,这一集合需要事先定义,而这一关键字的位置一般位于step后,如果用回想要在哪一分析部删除单元,就在哪一分析部后添加。 但是使用这一方法是要注意的是由于这个单元是一下子从模型中删除,所以在standard下可能造成模型总体刚度奇异,导致计算不收...
model.fieldOutputRequests.changeKey(fromName='F-Output-1',toName='Field Outputs')model.fieldOutputRequests['Field Outputs'].setValues(variables=('S','E','PEMAG','U','RF','CF'))#apply pressure topPt=(0.2,0.1,2.5)topFace=mInstance.faces.findAt((topPt,))topFaceRegion=regionToolset.Region...
单击Continue按钮,进入Edit Step对话框,如图5-5(a)所示,输入分析步描述:Heat transfer step,分析步类型选择Transient,输入分析步长为2.5;切换到Incrementation选项卡,如图5-5(b)所示,设置初始增量步Initial为0.01,最小Minimum为1E-007,输入Max.allowable temperature change per increment:10,单击OK按钮完成分析步创建...
*MODEL CHANGE, TYPE=ELEMENT, REMOVE Set-1 Set-1为所定义的单元集合,这一集合需要事先定义,而这一关键字的位置一般位于step后,如果用回想要在哪一分析部删除单元,就在哪一分析部后添加。 但是使用这一方法是要注意的是由于这个单元是一下子从模型中删除,所以在standard下可能造成模型总体刚度奇异,导致计算不收...