技术性能 安装底座共振 5 kHz min. 电压范围 0-10 to 0-100 mm/sec RMS ±10% Nominal 80 Hz at 22 °C 频率响应 10 Hz to 1 kHz ±5% - ISO10816 分离 底座分离 测量范围 50 g 峰值 横向灵敏度 小于5% 供电 输出电流 4-20 mA DC proportional to RMS velocity (mm/s)...
ParametricsCY8C4014SXI-420 Analog Blocks (Universal)- CAN0 CPUARM Cortex-M0 CapSenseY Comparators1 Continuous Time Blocks- DMA Channels0 EEPROM- FamilyPSOC 4000 Flash16 kByte Frequencymax16 MHz GPIOs5 I/O Pins5 I/O Pins (SIO)- JTAG and Si ID0x0A53119A ...
time / sec. Table for temperature vs. time during the air reflow process Tolerance of temperatures: ± 5 °C time / sec. 0 10 20 30 40 50 60 70 80 90 100 110 120 130 temperature / °C time / sec. temperature / °C 23 34 46 60 80 103 ...
-55 to +150 -55 to +100 260 for 10 sec 125 °C °C STG T Operating Temperature OPR T Lead Solder Temperature (Wave) Junction Temperature Range °C SOL T °C J (1) V Isolation Test Voltage 5000 Vac(rms) ISO (rms AC voltage, 60Hz, 1 min. duration)...
Agilent / HP 4395A Spectrum Network Impedance Analyzer: 10 Hz to 500 MHz + 010 Agilent / HP 4396B Network/Spectrum Analyzer 30- + FRESH CAL Agilent / HP 53150A CW Microwave Frequency Counter, 20 GHz AGILENT / HP 53181A RF FREQUENCY COUNTER 10 digit/sec. ...
Time 1 sec. to 60 sec, or infinite time. For infinitetime, the current can be max. 220A SamplingTime Automatic DischargedAh Measurement 0.1Ah to 10,000Ah 0.4% accuracy No. of PossibleMeasurement 14 ParallelConnection Max. 4 of testers can be connected; the connection set is ...
out disc diameter mm 400x50x203 280x50x203(min) 400x50x203 280x50x203(min) 400x50x203 280x50x203(min) 400x50x203 280x50x203(min) 400x50x203 280x50x203(min) Circumferential speeds m/sec 35 35 35 35 34.2 Work spindle speeds rpm 25-380 25-380 25-380 25-380 25...
“Maximum energy save mode” can be activated by pressing the button for 3 sec. After two hours of non-use, the machine switches to the maximum energy save mode. Press the energy save button to Machine may require a cold start Close the lever Close the lever 1 min. Ready Heating up 13...
Tool change time (adjacent tool) 1.2 Sec Positioning accuracy ± 0.005 mm Repeat positioning accuracy ± 0.003 mm Machine dimension (L×W×H) 1900*2070*2300 mm Machine weight 3500 kg Power requirement 10 KVA Required air pressure 6 kgf/cm² Required ga...
0.060" double amplitude ±0 Hz to 55 Hz, 35g’s 55 Hz to 2000 Hz º Soldering Condition 300 C for ±0 seconds Hermetic Seal Leak rate less than ± x ±0ꢀ+ atm.cc/sec Footnotes: ±) Standard frequency stability (±20, ±25, ±50 ppm & others available). 2) Jitter...