常用路由器配置命令集锦 1、进入特权模式、全局配置模式、接口配置模式、虚拟终端配置模式、RIP路由协议配置模式 Router > enable Password : Router # Router # configure terminal Router (config) # Router (config) # int f0/12 Router (config-if) #...
1.路由器的模式 Router>用户模式 Router#特权模式 Router(config)#配置模式 Router(config-if)# 接口模式 Router(config)#interface f0/0.1 进入子接口 Router(config-subif)# 子接口模式 Router(config-line)# 进行线模式 Router(config-router)# 路由配置模式 2.配置静态路由条目 Router(config)# ip route 192....
(注:配合路由协使用,用其中的一个动态路由号作默认路由配置)Router(config)# ip route 下一路由器 IP 地址 | 从本地出口的地址(注:只有一个公网地址时,在出口路由器上的配置)*内部路由选择协议*使用router和network命令Router(config)# router路由协议 rip I igrp I eigrp I ospf I is-is 等自主系统号...
2.常用命令 以下是一些常用的路由器配置命令: 2.1基本操作命令 - enable:进入特权模式。 - disable:退出特权模式,返回用户模式。 - exit:退出当前配置模式。 2.2接口配置命令 - show interfaces:查看接口信息。 - interface interface-name:进入指定的接口配置模式。 - ip address ip-address subnet-mask:配置接口的...
1、路由器口令设置 2、路由器配置 router(config)#int s0/0 进入Serail接口 router(config-if)#no shutdown 激活当前接口 router(config-if)#clock rate 64000 设置同步时钟 router(config-if)#ip address 设置IP地址 router(config-if)#ip address second 设置第二个IP ...
在进入接口配置模式后,使用 `interface Vlan <VLAN 号>` 命令来配置 VLAN 接口。可以配置接口的描述、IP 地质、子网掩码等。 示例: ``` [Router-Vlan10] description Management VLAN [Router-Vlan10] ip address 10:0:0.1 255.255.255:0 ``` 3、静态路由配置 使用`ip route-static <目的网络> <子网掩...
(1)使用命令disp cur可以看到端口E0/1属于vlan2,E0/2属于vlan3; (2)使用display interface Ethernet 0/1可以看到端口为access端口,PVID为2; (3)使用display interface Ethernet 0/2可以看到端口为access端口,PVID为3 5、交换机IP地址配置 功能需求及组网说明 ...
7、等同;在配置交换机和路由器时,可以写成:248、设备命名规则:地名 -设备名-系列号例:PingGu-R-S3600H3C华为交换机端口绑定基本配置 2008-01-2213:401,端口 MACa)AM命令使用特别的 AMUser-bind命令,来完成 MAC地址与端口之间的绑定。比方:[SwitchA]amuser-bindmac-address00e0-fc22-f8d3interfaceEthernet0/1...
display ndp #路由器设备命令—华三V5版本支持,现在改用display lldp neighbor-information display diagnostic-information #故障信息收集 02系统运行配置状态检查 display interface #接口流量、链路状态 dis current-configuration inter #地址分配 dis current-configuration |include ospf #路由扩散 ...