塑胶件颜色外观缺陷- 中英文对照 Bloom/ 花面 A non-continuous surface coating coming from additives in the plastics.胶件表面层非一个连续的注塑表面 Blush/泛红 Discoloration caused by plastic flow during molding, usually found near gates 由于在注塑成型中塑料流速导致的变色，通常在入口附近找出 B...
塑胶缺陷中英文对照表 1.Jetting喷射纹 2.Entrapped困气 3.Incompletely filled part/shortage shot缺胶 4.Surface Layer表面起层 5.Deformation变形 6.Air Steaks气纹 7.Dark Spots黑点 8.Stress-Whitening应力发白/应力裂痕 9.Ejector Marks顶针印 10.Burnt streaks烧焦痕 11.Overspray毛边 12.Sink marks/shrinka...
文档标签: 塑胶产品常见缺陷中英文对照 塑胶产品常见问题后加工产品常见问题刮檫花scratch电镀堆积heavyplating料花fowline漏电镀mis-platingweldline裂纹craze批峰fash断环brokenring碰伤damage尘点dustpointcutdamage少油mis-paint缺口chip色差aberrationpaintburning喷油不均incon ormitypaint模印mark积油heavypaint错位mismatch喷...
塑胶缺陷中英文对照表 1. Jetting 喷射纹 2. Entrapped 困气 3. Incompletely filled part/shortage shot 缺胶 4. Surface Layer 表面起层 5. Deation 变形 6. Air Steaks 气纹 7. Dark Spots 黑点 8. Stress-Whitening 应力发白/应力裂痕 9. Ejector Marks 顶针印 10.Burnt streaks 烧焦痕 11.Overspray...
塑胶缺陷中英文对照表1.Jetting喷射纹2.Entrapped困气3.Incompletelyfilledpart/shortageshot缺胶4.SurfaceLayer表面起层5.Deformation变形6.Air..
塑胶件主要缺陷中英文对照 主要缺陷中英文对照 序号中文英文序号中文英文 1披峰burr 16流痕Flow mark 2缺胶Short shot 17色差abberration 3变形/注塑后变形Deformation 18夹水线Weld lines 4偏模Mismatch 19碰伤Bump damage 5起泡Blister 20银线Silver 6污斑Grease pits21少数量Packing shortage 7雾化Atomization 22...
塑胶产品常见缺陷中英文对照 塑胶产品常见问题刮檫花料花夹水线(融接痕)批峰碰伤削伤(剪伤)缺口困气(烧焦)模印错位顶高凹痕拉裂拉伤发亮发白发黄混色黑点杂料缩水颗粒堵孔变形流痕水口冲印水口余料纹理不均手印缺胶起级间隙脏污毛丝&胶丝气泡多胶弯曲骨位槽位少数白点螺丝孔倒扣scratchflowlineweldlineflashdamage...
塑胶注塑缺陷中英文对照.doc 文档分类:汽车/机械/制造|页数:约4页 分享到: 1/4 分享到: 1/4下载此文档 文档列表文档介绍 pletelyfilledpart/shortageshot缺胶肇SurfaceLayer表面起层莄Deformation变形罿AirSteaks气纹蕿DarkSpots黑点蒆Stress-Whitening应力发白/应力裂痕膄EjectorMarks顶针印羀Burntstreaks烧焦痕螇...
塑胶产品常见缺陷中英文对照概述.pdf,塑胶产品常见问题 后加工产品常见问题 刮檫花 scratch 电镀堆积 heavy plating 料花 flow line 漏电镀 mis-plating 夹水线 ( 融接痕) weld line 裂纹 craze 批峰 flash 断环 broken ring 碰伤 damage 尘点 dust point 削伤( 剪伤) cut d