(PULLUP) Internal pullup current from BAT pin to LD pin, used for load detect functionality VBAT ≥ 4.7 V, VLD = VSS 35 100 172 µA RPD Internal pulldown resistance on LD pin in SHUTDOWN mode VBAT ≥ 4.7 V 80 kΩ 6.8 Precharge (PCHG) and Predischarge (PDSG) FET Drive Typical...
35μA/ 電源,MSOP-10 パッケージ トリプルPチャネル・コントローラ,2.5V 〜 36V, SSOP-24および QFN-24 パッケージ デュアルNチャネル,9V 〜 80V,SO-16,MSOP-16および DFN-14 パッケージ Nチャネル,4V 〜 80V,MSOP-8および DFN-6 パッケージ 24 リニアテクノロジー...
14-Bit ADC Result 0x1800 0x1F10 ADC Result in Decimal 6144 7952 GAIN (µV/LSB) 380 380 OFFSET (mV) 30 30 Cell Voltage (mV) 2365 3052 Note When entering NORMAL mode from SHIP mode, please allow for the following times before reading out initial cell voltage data: BQ76920: 250 ms ...
3.5 3 2.5 2 1.5 1 0.5 TYP MAX 0 10 20 30 40 50 60 70 80 90 RH ( %RH) 相対湿度 (%RH) 精度 代表的なアプリケーション 英語版の TI 製品についての情報を翻訳したこの資料は,製品の概要を確認する目的で便宜的に提供しているものです.該当する正式な英語版の最新情報は, www.ti....
min/max values stated where TA = -40°C to 85°C and VBAT = 4.7 V to 80 V (unless otherwise noted)(1) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT I(PULLUP) Internal pullup current from BAT pin to LD pin, used for load detect functionality VBAT ≥ 4.7 V, VLD = VSS 35 100 172...
Total Harmonic Distortion + Noise vs HP Power 20 0 ±20 ±40 ±60 ±80 0dBFS ±100 ±120 ±140 ±160 ±180 0 4000 8000 12000 16000 20000 Frequency (Hz) C008 (16-Ω Load) 図 6-15. AINL TO HP FFT Amplitude at 0 dBFS vs Frequency 0 ±10 ±20 ±30 ±40 ±50 ±60 ±70 ±...
A small amount of hysteresis has been provided by the 10kΩ and 10MΩ resistors to insure fast switching when the RC time constant is chosen to give long delay times. A good starting point is R = 100kΩ and C = 0.01µF to 1µF. All outputs immediately go low when VIN falls ...
0 -20 -40 -60 -80 -100 -120 -140 -160 0 8 16 24 Normalized Frequency (x fS) 図 6-5. Decimation Filter Stop Band Characteristic 32 0 -5 -10 -15 -20 -25 -30 -35 -40 -45 -50 0 0.1 0.2 0.3 Normalized Frequency (x fS/1000) 図 6-7. High-Pass Filter Characteristic 0.4 ...
• The switching frequency is set above the AM-band with 44 times the input sample rate of 48 kHz which results in a frequency of 2.11 MHz. • The selection of a 2.11 MHz switching frequency enables the use of a small output inductor value of 3.3 µH which leads to a very small...
Idle Channel Noise vs Supply Voltage 0 Ch 1 to Ch 2 Ch 2 to Ch 1 -20 -40 -60 -80 -100 -120 20 100 1k Frequency (Hz) PVDD = 24 V RL = 8 Ω図 5-35. Crosstalk 10k 20k PO = 1W 18 資料に関するフィードバック (ご意見やお問い合わせ) を送信 Product Folder Links: TAS...