在Logisim中,设计一个高电平有效2线-4线译码器,使能Enable高电平有效。 相关知识 译码器(Decoder)能将二进制代码的特定含义翻译出来,是一类多输入多输出组合逻辑器件,其可以分为:变量译码和显示译码两类。 变量译码器一般是一种较少输入变为较多输出的器件,常见的有n线-2^n线译码和BCD码译码两类;显示译码器用来...
wire [29:0] code = code8b10b[i] ; wire [9:0] expect_0_disp = {code[11], code[12], code[13], code[14], code[15], code[16], code[17], code[18], code[19], code[20]} ; wire [9:0] expect_1_disp = {code[1], code[2], code[3], code[4], code[5], code[6]...
然后再申明输出信号的clk、rst、enalbes other control signals、data signals; (16)在例化模块时,使用名字相关的显式映射而不要采用位置相关的映射,这样可以提高代码的可读性和方便debug 连线错误; (17)如果同一段代码需要重复多次,尽可能使用函数,如果有可能,可以将函数通用化,以使得它可以复用。注意,内部函数的定...
只有for-loop语句是可以综合的。 14、设计时序电路时,建议变量在always语句中赋值,而在该always语句外使用,使综合时能准确地匹配。建议不要使用局部变量。 15、不能在多个always块中对同一个变量赎值 16、函数 函数代表一个组合逻辑,所有内部定义的变量都是临时的,这些变量综合后为wire。 17、任务: 任务可能是组...
Case statements are used where we have one variable which needs to be checked for multiple values. like an address decoder, where the input is an address and it needs to be checked for all the values that it can take. Instead of using multiple nested if-else statements, one for each val...
UDP frame transmitter with 64 bit datapath for 10G/25G Ethernet. udp_muxmodule UDP frame multiplexer with parametrizable data width and port count. Supports priority and round-robin arbitration. xgmii_baser_dec_64module XGMII 10GBASE-R decoder for 10G PCS/PMA PHY. ...
4. 模块的命名。在系统设计阶段应该为每个模块进行命名。命名的方法是,将模块英文名称的各个单词首字母组合起来,形成3到5个字符的缩写。若模块的英文名只有一个单词,可取该单词的前3个字母。各模块的命名以3个字母为宜。例如:Arithmatic Logical Unit模块,命名为ALU。Data Memory Interface模块,命名为DMI。Decoder模块...
(e.g. one 8-bit lane and eight 8-bit lanes, but not one 16-bit lane and one 32-bit lane). Second, the bus widths must be related by an integer multiple (e.g. 2 words and 6 words, but not 4 words and 6 words). Wait states will be inserted on the wider bus side when ...
for(i=0,i<4,i=i+1) if(key[i]) decoder = i; else decoder = decoder; end endmodule 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 6、利用任务实现串行移位乘法器 ...
268 (256 Dx.y and 12 Kx.y)");$display("valid inputs, with both + and - starting disparity.");$display("We check that the encoder output and ending disparity is correct.");$display("We also check that the decoder matches.");for(i =0;i<268;i = i +1)begin// testin = code...