Error (12857): HIP reset pin "i_pcie_perst" is locked to "PIN_BD35", which is not legal. The pins that I assigned are output signals which goes to the transceiver, and are placed in: set_location_assignment PIN_W41 -to o_serial_data_GBT[0] set_location_assign...
表1. SFP连接器引脚配置 Table 1. SFP Connector Pin Assignment DS28CZ04用作SFP的串行控制接口 如图2框图所示,DS28CZ04由2线串行接口、4kb EEPROM以及4个双向PIO组成,该器件通过工作在标准模式或快速模式的I²C接口与主处理器连接。DS28CZ04通过一个内存地址和两个从地址(通常为A0h、A2h)寻址512个存储器地...
SFF=插拔式单纤收发一体模块SmallFormFactorTransceiver 中心波长速率功率激光器工作温度电压连接类型 1310TX/1550RX155MS=小功率-15~-8dBmFP0~+70℃3.3VDCSC/UPC PinAssignment 1RXGNDReceiverSignalGround2VCCRReceiverPowerSupply3SDSignalDetect.4RD–isanopen-emitteroutputcircuit.5RD+isanopen-emitteroutputcircuit....
Table7-Pin Assignment Pin Logic Symbol Name/Description Note 1 VeeT Module Transmitter Ground Note1 2 LVTTL-O TX_Fault Module Transmitter Fault Note2 3 LVTTL-I TX_Disable Transmitter Disable; Turns off transmitter laser output Note3 4 LVTTL-I/O SDA 2-wire Serial Interface Data Line (Same as...
Pin Assignment and Pin Description Figure1. Diagram of host board connector block pin numbers and names Pin Symbol Name/Description Notes 1 V EET Transmitter Ground (Common with Receiver Ground) 1 2 T FAULT Transmitter Fault. 2 3 T DIS ...
Pin Assignment Pin out of Connector Block on Host Board Pin Symbol Name/Description NOTE 1 VEET Transmitter Ground (Common with Receiver Ground) 1 2 TFAULT Transmitter Fault. 2 3 TDIS Transmitter Disable. Laser output disabled on high or open. 3 4 SDA...
Power Pin Assignment Mode a 1/2(+), 3/6(-) Poe Distance up to 100m Poe Standard 802.3af, 802.3at, Max 30W Output Firewall Without Firewall Transfer Rate 10/100/1000Mbps Network Ethernet Performance Store-and-Forward Transport Package Unit Packge...
Power Pin Assignment Mode a 1/2(+), 3/6(-) Port 24*10/100/1000m Tx and 2 SFP Poe Distance up to 100m Poe Standard 802.3af, 802.3at, Max 30W Output Network Site Intermediate Node Routers Firewall Without Firewall Transfer Rate 10/100/1000Mbps Por...
Pin Assignment Pin out of Connector Block on Host Board Pin Symbol Name/Description NOTE 1 VEET Transmitter Ground (Common with Receiver Ground) 1 2 TFAULT Transmitter Fault. 2 3 TDIS Transmitter Disable. Laser output disabled on high or open. 3 4 SDA 2-wire S...
Figure 1 SFP28 Pad Assignment Top View Pin No Symbol Name/Description Power Seq. Note 1 VeeT Transmitter Ground 1st 1 2 TX_Fault Transmitter Fault 3rd 2 3 TX_Disable Transmitter Disable 3rd 3 4 SDA 2-Wire Serial Interface Data Line 3rd 4 5 SCL 2-Wire Serial Interface Data Line 3rd 4...