MUST_CLOSE: 执行“过账清算” 当执行“单级处理确定”时,不能点击红圈中的图标执行,需要点击“参数”进入参数设置界面,并输入命令MUST_SETTLE强制执行。 如上图,在命令框中输入MUST_SETTLE,回车即可强制执行“单级处理确定”, 运行结果如下图。 返回到CKMLCP主界面,刷新状态后,可以发现“单级确定处理”执行成功。
MUST_COGS: 执行“消耗重估” MUST_WIP: 执行“在产品重新评估” MUST_CLOSE: 执行“过账清算” 当执行“单级处理确定”时,不能点击红圈中的图标执行,需要点击“参数”进入参数设置界面,并输入命令MUST_SETTLE强制执行。 如上图,在命令框中输入MUST_SETTLE,回车即可强制执行“单级处理确定”, 运行结果如下图。
MUST_CLOSE: 执行“过账清算” 当执行“单级处理确定”时,不能点击红圈中的图标执行,需要点击“参数”进入参数设置界面,并输入命令MUST_SETTLE强制执行。 如上图,在命令框中输入MUST_SETTLE,回车即可强制执行“单级处理确定”, 运行结果如下图。 返回到CKMLCP主界面,刷新状态后,可以发现“单级确定处理”执行成功。
MUST_CLOSE: 执行“过账清算” 当执行“单级处理确定”时,不能点击红圈中的图标执行,需要点击“参数”进入参数设置界面,并输入命令MUST_SETTLE强制执行。 如上图,在命令框中输入MUST_SETTLE,回车即可强制执行“单级处理确定”, 运行结果如下图。 返回到CKMLCP主界面,刷新状态后,可以发现“单级确定处理”执行成功。
Since we are in July, there are no need to use 'must settle'- if you allow postings on previous period on MMPV, you can settle using cockpit orCKMH if settlement is single (not multi). Hope that helps. regards Patricia You must be a registered user to add a comment. If you've al...
(Settle Route Data) to the Route Execution:Once you open the Settle Route Data, can be filter with some parameters.The Route ID in standard is the same number as the FO number from TM.When we get inside in The Route, we can see the sequence of the process:Check OutCustomer Documents...
Archiving & Deletion Process stepsProsNo need for additional archiving-specific configurations.You don’t need to be an archiving expert to execute these steps.ConsArchiving-specific roles must be assigned to your user for access and execution.Client-Wide Article DiscontinuationIn this phase, articles...
• settle a date for the interview 确定面试的日期 • It was settled that they would meet in Beijing. 他们已经决定在北京见面。 5. 支付;结算 • settle an account 结账 • settle the charge for a taxi 付出租车费 6. 安排,安置 • You must settle all your affairs before you...
This is why read enabled must not be used in this scenario. As already explained, the secondary SAP HANA database must run with memory resource restrictions. The HA/DR provider needs to remove these memory restrictions when a takeover occurs. This is why multi SID (also MCOS) must not be...
Single Level is "Must_Settle", Multi-level is "Must_Multi", Revaluation of Consumption is "Must_COGS", WIP Revaluation (if using), is "Must_WIP", Closing Entry is "Must_Close". You type the Must transaction into the t-code box and press enter, not Execute to run the previous ...