<HUAWEI>display interface briefInUti/OutUti: input utility/output utility Interface PHY Protocol InUti OutUti inErrors outErrors Eth-Trunk1 up up 0% 0% 0 0GE0/0/2up up 21% 42% 634 0GE0/0/3up up 36% 37% 979 0GE0/0/4up up 31% 42% 978 0 ...
Interface PHY Protocol InUti OutUti inErrors outErrors MEth0/0/1 down down 0% 0% 0 0 NULL0 up up(s) 0% 0% 0 0 Vlanif1 up up -- -- 0 0XGigabitEthernet0/0/1 up up 0.01% 0% 0 0XGigabitEthernet0/0/2 down down 0% 0% 0 0 原因分析 为增加ACU2和交换机间的链路带宽和提高链路...
[SW1]display eth-trunk Eth-Trunk1's state information is: WorkingMode: NORMAL Hash arithmetic: According to SIP-XOR-DIP Least Active-linknumber: 1 Max Bandwidth-affected-linknumber: 8 Operate status: up Number Of Up Port In Trunk: 4 --- PortName Status Weight GigabitEthernet0/0/2 Up 1 ...
0 Eth-Trunk1 ROOT FORWARDING NONE 注意：①STP生成树的选举将Eth-Trunk1 当成一个接口来对待；②BPDU报文只会从一条链路发出；③为了放环，对于SW1来从一个接口收到BPDU，是不会从同一个Eth-Trunk 1中其他的接口转发出去的；LACP： Link Aggregation Control Protocol ①两台设备通过交互LACP报文协商...
0 Eth-Trunk1 DESI FORWARDING NONE # 查接口 <SW1>dis interface brie | incl Eth-Trunk1 Interface PHY Protocol InUti OutUti inErrors outErrors Eth-Trunk1 up up 0% 0% 0 0 # SW2的配置 sys sysn SW2 interface eth-trunk 2 int g0/0/1 ...
1、Eth-Trunk接口的概念 Eth-Trunk接口,是基于链路聚合(Link Aggregation)技术。链路聚合技术又是基于IEEE802.3ad标准“链路聚合控制协议(LACP,Link Aggregation Control Protocol)”,以实现链路动态聚合与解聚合的协议。Eth-Trunk又叫以太网链路聚合Eth-Trunk,它通过将多条以太网物理链路捆绑在一起成为一条逻辑链路。将...
将eth0/0/1加入eth-trunk 1接口 [L1]interface Ethernet0/0/1 [L1-Ethernet0/0/1]eth-trunk 1 [L1-Ethernet0/0/1]display interface Eth-Trunk 1 Eth-Trunk1 current state : UP Line protocol current state : UP Description: Switch Port, PVID : 1, Hash arithmetic : According to SIP-XOR-DIP...
<HUAWEI> display interface 10ge 1/0/1 10GE1/0/1 current state : UP (ifindex: 4) Line protocol current state : UP 如果显示为UP则表示接口处于正常启动的状态,请执行步骤3。 如果显示不是UP,请检查Eth-Trunk成员接口的物理链路、光模块情况。
成员接口处于Up状态时才能被Eth-Trunk选中。在任意视图下执行display interface interface-type interface-number命令查看Eth-Trunk成员接口的物理状态,其中current state表示接口的物理状态。 <HUAWEI>displayinterface10ge1/0/1 10GE1/0/1currentstate:UP(ifindex:4) Lineprotocolcurrentstate:UP ...
(ld): LDT block (lb): LBDT block (lp): Loop-detect block (ms): MACsec down (o): Observe-port forwarding down InUti/OutUti: input utility/output utility Interface PHY Protocol InUti OutUti inErrors outErrors GigabitEthernet1/0/0up up0.01% 0.01% 0 0 GigabitEthernet1/0/1up up0.01% 0.01...