在配置Eth-Trunk接口时,是否能够配置IP地址取决于Eth-Trunk接口的工作模式。通常情况下,Eth-Trunk接口默认是二层接口,不能直接配置IP地址。但如果将Eth-Trunk接口切换为三层接口,则可以配置IP地址。以下是详细的步骤: 确认网络设备型号和系统: 在进行任何配置之前,首先需要确认网络设备的型号和操作系统版本,以确保配置...
Eth-Trunk接口能配置IP地址吗 链路聚合接口即Eth-Trunk接口为二层接口时,不能配置IP地址。如果在Eth-Trunk接口视图执行undo portswitch命令将接口切换成三层接口,可以配置IP地址。 翻译 收藏 下载文档 更新时间:2024-11-04 文档编号:EDOC1100305532 浏览量:715034 ...
1、首先在交换机上行创建Eth-trunk接口,并更改其工作模式为LACP [S1]interface Eth-Trunk 1 [S1-Eth-Trunk1]mode lacp [S2]interface Eth-Trunk 1 [S2-Eth-Trunk1]mode lacp 1. 2. 3. 4. 2、将接口划入Eth-Trunk中 [S1]interface GigabitEthernet 0/0/3 [S1-GigabitEthernet0/0/3]eth-trunk 1 [S...
命令:interface Eth-trunk <trunk-id> 配置链路聚合。 这条命令创建了一个Eth-Trunk口,并且进入该Eth-Trunk口视图。trunk-id用来唯一标识一个Eth-Trunk口,该参数的取值可以是0到63之间的任何一个整数。如果指定的Eth-Trunk口已经存在,执行interface eth-trunk命令会直接进入该Eth-Trunk口视图。 SWA的配置: SWB的...
配置BGP的基本功能 操作步骤 进入系统视图。 system-view 进入BGP视图。 bgpas-number 进入IPv4单播地址族视图。 ipv4-familyunicast 配置BGP感知Eth-Trunk接口状态。 peerpeerIpv6Addrroute-priority-trackinterface{interface-name|localIfTypelocalIfNum} 该命令的优先级高于邻居出入口策略配置(peer route-policy命令)。
配置手工负载分担模式 [L1]interface Eth-Trunk 1 //创建eth-trunk 1接口 [L1-Eth-Trunk1]mode manual load-balance //设置为手工负载分担模式 [L1-Eth-Trunk1] 将eth0/0/1加入eth-trunk 1接口 [L1]interface Ethernet0/0/1 [L1-Ethernet0/0/1]eth-trunk 1 ...
IFPDT/4/VXLANHASHNOTSUPPORT:OID [OID] The Eth-Trunk can not function normally as an outbound interface for vxlan packets when IP address-based load balancing is configure
百度试题 结果1 题目手工链路聚合模式下的Eth-Trunk端口,其传输速率与( )有关。(多选)A.成员端口处于公网还是私网B.成员端口上是否配置了IP地址C.成员端口的数量D.成员端口的带宽 相关知识点: 试题来源: 解析 CD 反馈 收藏
ALM-3276800089 当Eth-Trunk接口作为VXLAN业务的出接口时,该接口配置的普通IP负载分担方式对VXLAN报文不生效 Eth-Trunk口。 在“高级”页面下选择“负载均衡”,选择“目的MAC地址”。 结束。 使用设备命令行方式清除告警。 在Eth-Trunk口下执行命令load-balance {dst-mac},按照MAC地址进行负载分担。检查告警是否消除。