{ struct iphdr t; unsigned short *s; memset(&t,0,2); s = (unsigned char *)&t; //注意,直接赋值0x8183,因为该常量必然和主机字节序一致, //小端:83给低字节, //大端:81给低字节 *s = 0x8183; printf(“fin:%d rsv:%d opcode:%d mask:%d paylod:%d ”, t.fin,t.rsv,t.opcode,t.mas...
我们定义IP包头结构体为: struct iphdr { #if defined(__LITTLE_ENDIAN_BITFIELD) __u8 ihl:4, version:4; #elif defined (__BIG_ENDIAN_BITFIELD) __u8 version:4, ihl:4; #else #error "Please fix <asm/byteorder.h>" #endif __u8 tos; __u16 tot_len; __u16 id; __u16 frag_off; _...
struct iphdr { #if defined(__LITTLE_ENDIAN_BITFIELD) //小端模式 __u8 ihl:4, version:4; #elif defined(__BIG_ENDIAN_BITFIELD) //大端模式 __u8 version:4, ihl:4; #endif __u8 tos; __u16 tot_len; __u16 id; __u16 frag_off; __u8 ttl; __u8 protocol; __u16 check; __u32 ...
enum Date today = Monday; int iphdr1=10; extern void func1(); extern void func2(int x); extern int func3(char *); extern char * func4(int x, int y); int fun5(int a) { struct udphdr udp2; func1(); printf("aaaaaaaaaaa\n"); } int fun6(char *a) { static struct udph...
{ int i,iphdrlen; struct ip *ip; struct icmp *icmp; struct timeval *tvsend; double rtt; ip=(struct ip *)buf; iphdrlen=ip->ip_hl<<2; /*求ip报头长度,即ip报头的长度标志乘4*/ icmp=(struct icmp *)(buf+iphdrlen); /*越过ip报头,指向ICMP报头*/ ...
iphdrlen=ip->ip_hl<<2;/*求ip报头长度,即ip报头的长度标志乘4*/icmp=(structicmp *)(buf+iphdrlen);/*越过ip报头,指向ICMP报头*/len-=iphdrlen;/*ICMP报头及ICMP数据报的总长度*/if( len<8)/*小于ICMP报头长度则不合理*/{ printf("ICMP packets\'s length is less than 8\n");return-1; ...
字节的倍数. 描述 === struct iphdr { BYTE versionihl; BYTE tos;WORD tot_len; WORD id; WORD frag_off; BYTE ttl; BYTE protocol; WORD check; DWORD saddr; DWORD daddr; /* Put options here. */ }; 二、TCP 头格式 TCP 头格式 源端口 (16 位) 目的端口 (16 位) 序号 (32 位) 确认号...
ping命令是用来查看网络上另一个主机系统的网络连接是否正常的一个工具。ping命令的工作原理是:向网络上的另一个主机系统发送ICMP报文,如果指定系统得到了报文,它将把报文一模一样地传回给发送者,这有点象潜水艇声纳系统中使用的发声装置。要真正了解ping命令实现原理,
本程序定义了3个结构体:-iphdr、-icmphdr、和-ipotionhdr,分别用于存放IP报头信息、ICM P报头信息和IP路由选项信息。 1.定义IP报头结构体 Typedef struct _iphdr { Unsigned int h_len:4; Unsigned int version:4; Unsigned char tos; Unsignedshort total_len; ...
我有以下代码,它只捕获数据包并打印IP源和目的地:#include <linux/kernel.h>#include <linux/netfilter_ipv4.h> unsigned= (struct iphdr *)skb_ 浏览12提问于2021-12-01得票数 0 回答已采纳 1回答 如何使用C程序将IP地址设置为计算机? 、、、 我有一个硬代码(C代码)来打印我的计算机IP地址,我将根据一些...