1.1.1 password-recovery enable password-recovery enable命令用来使能密码恢复功能。 undo password-recovery enable命令用来关闭密码恢复功能。 【命令】 password-recovery enable undo password-recovery enable 【缺省情况】 密码恢复功能处于使能状态。 【视图】 ...
1. `password-recovery enable`:启用密码恢复功能,当用户忘记密码时,可以通过特定流程重置密码。2. `password-control enable`:启用密码控制功能,对用户密码的使用和更改进行管理。3. `undo password-control history enable`:取消启用密码历史记录功能,允许用户重复使用旧密码。4. `password-control length 8`:设置密...
1.1.34 password-recovery enable 1.1.35 reboot 1.1.36 reset scheduler logfile 1.1.37 reset version-update-record 1.1.38 restore factory-default 1.1.39 scheduler job 1.1.40 scheduler logfile size 1.1.41 scheduler reboot at 1.1.42 scheduler reboot delay 1.1.43 scheduler schedule 1.1.44 shutdown...
启用LLDP全局功能: lldp global enable 1. 启用环路检测功能: loopback-detection global enable vlan 1 to 4094 1. 配置系统工作模式为标准模式: system-working-mode standard 1. 配置XBAR负载均衡: xbar load-balance 1. 启用密码恢复功能: password-recovery enable 1. 配置VLAN和接口IP地址: vlan 5 descripti...
password-recovery enable # vlan 1 # vlan 2 to 20 # vlan 100 # vlan 230 # stp instance 0 root primary stp global enable # interface NULL0 # interface Vlan-interface1 # interface Vlan-interface2 ip address 10.132.2.1 255.255.254.0
password-recoveryenable # vlan1 # vlan78 nameworkstation # vlan80 nameserver # vlan83 namemanage # domainsystem access-limitdisable stateactive idle-cutdisable self-service-urldisable # user-groupsystem group-attributeallow-guest # local-userQYJY passwordcipher$c$3$R0DKqcgoobd+B6KaAFFmoA5/zkyxh...
Enter the new password for the admin user: Re-enter the new password: The Password Recovery feature is enabled. Enter new value (enable,disable)[enable]: 说明: a.在登录提示时输入用户名Recover,密码也是Recover。 b.在系统提示的时间内(30秒),对交换机断电,再加电。 c.系统重新启动后,会提示您输...
04配置使能口令enable password cisco以cisco为例 switch>enable switch #c onfigure terminal switch(conf)#hostnameaptch2950 aptech2950(conf)# enable passwordcisco 05配置使能密码enable secretciscolab以cicsolab为例 switch>enable switch#c onfigure terminal ...
[H3C]undo superpassword //删除用户分级密码 [H3C]localuser bigheap 1234561 //Web网管用户设置,1为管理级用户 [H3C]undo localuser bigheap //删除Web网管用户 [H3C]user-interface aux 0 //只支持0 [H3C-Aux]idle-timeout 250 //设置超时为2分50秒,若为0则表示不超时,默认为5分钟 ...
[H3C-vty]undo set authenticationpassword //取消密码 [H3C]displayusers //显示用户 [H3C]displayuser-interface //用户界面状态 3、vlan配置 [H3C]vlan 2 //创建VLAN2 [H3C]undo vlanall //删除除缺省VLAN外的所有VLAN,缺省VLAN不能被删除 [H3C-vlan2]port Ethernet 0/4 to Ethernet0/7 //将4到7号...